Pages

Monday, 30 March 2015

MULTIPOINT FUEL INJECTION

MULTIPOINT FUEL INJECTION


Fuel injection is a method or system for admitting fuel into the internal combustion engine.There are basically two ways of admitting fuel one is through carburetor and other is fuel injection system.But presently the most used injection system are MPFI in petrol engine and CRDI in diesel engine.



Multi point fuel injection is a system wherein fuel is injected into individual cylinders based on commands from "on board engine management system computer"-popularly known as Engine control unit.ECU receives feed back from several sensors like engine speed sensor, fly wheel position sensor, vehicle speed sensor, atmospheric temp. sensor, accelerator pedal position sensor intake airflow sensor. Then ECU control the correct amount of fuel to be injected and the proper time at which the fuel will be injected at any speed and load condition. This ensure maximum power output at minimum fuel.


MPFI systems are of three types, first is BATCHED in which fuel is injected to the cylinders in groups, without precisely bringing together to any particular cylinder’s intake stroke, the second one is simultaneous in which fuel is injected at the same time to all the cylinders and the third one is sequential in which injection is timed to coincide with each cylinder’s intake stroke.

ADVANTAGES OF MPFI
  • More uniform air-fuel mixture will be supplied to each cylinder, hence the difference in power developed in each cylinder is minimum. 
  • The vibrations produced in MPFI engines is very less, due to this life of the engine component is increased. 
  • No need to crank the engine twice or thrice in case of cold starting as happen in the carburetor system. 
  • Immediate response, in case of sudden acceleration and deceleration. 
  • The mileage of the vehicle is improved. 
  • More accurate amount of air-fuel mixture will be supplied in these injection system. As a result complete combustion will take place. This leads to effective utilization of fuel supplied and hence low emission level. 

RACK AND PINION GEAR

RACK AND PINION GEAR



                   Rack and pinion gears are used to convert rotation into linear motion.The circular pinion engages teeth on a flat bar - the rack. Rotational motion applied to the pinion will cause the rack to move to the side, up to the limit of its travel.The rack and pinion arrangement is commonly found in the steering mechanism of cars or other wheeled, steered vehicles.A good example of a ‘rack and pinion’ gear system can be seen on trains that are designed to travel up steep inclines. The wheels on a train are steel and they have no way of griping the steel track. Usually the weight of the train is enough to allow the train to travel safely and at speed along the track. However, if a train has to go up a steep bank or hill it is likely to slip backwards. A ‘rack and pinion’ system is added to some trains to overcome this problem. A large gear wheel is added to the centre of the train and an extra track is, with teeth, called a ‘rack’ is added to the track. As the train approaches a steep hill or slope the gear is lowered to the track and it meshes with the ‘rack’. The train does not slip backwards but it is pulled up the steep slope.



Application:-

                  Rack and pinion gears provide a less mechanical advantage than other mechanisms, but greater feedback and steering sensation. A rack and pinion gear gives a positive motion especially compared to the friction drive of a wheel in tarmac. In a rack and pinion railway, a central rack between the two rails engages with a pinion on the engine allowing a train to be pulled up very steep slopes.

                  Rack and pinions gears are commonly used in the steering system of cars to convert the rotary motion of the steering wheel to the side to side motion in the wheels. The steering wheel rotates a gear which engages the rack. As the gear turns, it slides the rack either to the right or left, depending on which way the wheel is turned. Rack and pinion gears are also used in some scales to turn the dial that displays a weight.

MECHANICAL ENGINEERING INTERVIEW QUESTIONS

MECHANICAL ENGINEERING INTERVIEW QUESTIONS
1.)What is enthalpy?
Ans:-Enthalpy is the heat content of a chemical system.
2.) What is a positive displacement pump?
Ans:-A positive displacement pump causes a liquid or gas to move by trapping a fixed amount of fluid or gas and then forcing (displacing) that trapped volume into the discharge pipe. Positive
displacement pumps can be further classified as either rotary­type (for example the rotary vane)or lobe pumps similar to oil pumps used in car engines. These pumps give a non­pulsating output or displacement unlike the reciprocating pumps. Hence, they are called positive displacement pumps.
3.) Why would you use hydraulics rather than pneumatics?
Ans:-Hydraulics is suitable for higher forces & precise motion than pneumatics. This is because hydraulic systems generally run at significantly higher pressures than pneumatics systems.Movements are more precise (repeatable) because hydraulics uses an incompressible liquid to transfer power whilst pneumatics uses gases.Pneumatic systems have some advantages too. They are usually significantly cheaper than hydraulic systems, can move faster (gas much less viscous than oil) and do not leak oil if they
develop a leak.

MECHANICAL ENGINEERING QUESTIONS



MECHANICAL ENGINEERING QUESTIONS

1.)What is the difference between shear center flexural center of twist and elastic center?
Ans:-The shear center is the centroid of a cross­section. The flexural center is the center of twist, which is the point on a beam that you can add a load without torsion. The elastic center is located at the center of gravity. If the object is homogeneous and symmetrical in both directions of the cross ­section then they are all equivalent.

2.) Explain Otto cycle.
Ans:-Otto cycle can be explained by a pressure volume relationship diagram. It shows the functioning cycle of a four stroke engine. The cycle starts with an intake stroke, closing the intake and moving to the compression stroke, starting of combustion, power stroke, heat exchange stroke where heat is rejected and the exhaust stroke. It was designed by Nicolas Otto, a German engineer.

3.)What is ductile­ brittle transition temperature?
Ans:-It is the temperature below which the tendency of a material to fracture increases rather than forming. Below this temperature the material loses its ductility. It is also called Nil Ductility Temperature.

4.)What is isometric drawing?
Ans:-It is a 3­D drawing used by draftsmen, architects etc

MECHANICAL ENGINEERING INTERVIEW QUESTIONS



MECHANICAL ENGINEERING INTERVIEW QUESTIONS

1.)Which conducts heat faster steel copper or brass?
Ans:-Copper conducts heat faster than steel or brass. Any material that is good for conducting heat is also good for electricity in most cases. Wood terrible for transferring heat thus is also insulator for electric.

2.) What is a Process Flow Diagram?
Ans:-A Process Flow Diagram (or System Flow Diagram) shows the relationships between the major components in the system. It also has basic information concerning the material balance for the process.

3.) Where pneumatic system is used?
Ans:-Any system needs redundancy in work needs pneumatics, because the compressor of the pneumatic system has periodical operations (intermittent work, not as hydraulic pump). The compressed air could be accumulated in tanks with high pressures and used even if the compressor failed.

MECHANICAL ENGINEERING INTERVIEW QUESTIONS



MECHANICAL ENGINEERING INTERVIEW QUESTIONS

1.)Why gas containers are mostly cylindrical in shape?
Ans:-The most efficient shape for withstanding high pressure is a sphere but that would be costly to manufacture. A cylinder with a domed top and a domed bottom (look underneath, the flat base is actually welded around the outside, the bottom of the gas container is actually domed) is a much cheaper shape to manufacture whilst still having good strength to resist the internal gas pressure.

2.) How is martensite structure formed in steel?
Ans:-Martensite transformation begins when austenite is cooled below a certain critical temperature,called the matrensite start temperature. As we go below the martensite start temperature, more and more martensite forms and complete transformation occurs only at a temperature called martensite finish temperature. Formation of martensite requires that the austenite phase must be cooled rapidly.

3.) What is an orthographic drawing?
Ans:-Orthographic projections are views of a 3D object, showing 3 faces of it. The 3 drawings are aligned so that if the page were folded, it would create part of the shape. It is also called multiview projections.The 3 faces of an object consist of its plan view, front view and side view. There are 2 types of orthographic projection, which are 1st angle projection and 3rd angle projection.

MECHANICAL ENGINEERING INTERVIEW QUESTIONS



MECHANICAL ENGINEERING INTERVIEW QUESTIONS

1.)What does angular momentum mean?
Ans:-Angular momentum is an expression of an objects mass and rotational speed. Momentum is the velocity of an object times it is mass, or how fast something is moving how much it weigh. Therefore, angular momentum is the objects mass times the angular velocity where angular velocity is how fast something is rotating expressed in terms like revolutions per minute or radians per second or degrees per second.

2.)What is the role of nitrogen in welding?
Ans:-Nitrogen is used to prevent porosity in the welding member by preventing oxygen and air from entering the molten metal during the welding process. Other gases are also used for this purpose such as Argon, Helium, Carbon Dioxide, and the gases given off when the flux burns away during SMAW (stick) welding.

3.) What causes white smoke in two stroke locomotive engines?
Ans:-That is the engine running too lean (lack of fuel). This condition will lead to overheating and failure of the engine.